HC2 with 2008 infinity G35

Available in Canada and USA
Post Reply
RWarrior
12Volt Specialist
Posts: 11
Joined: Wed Jan 15, 2014 10:08 am

HC2 with 2008 infinity G35

Post by RWarrior » Tue Jan 31, 2017 4:34 pm

I've got issues with this combo..


Sometimes the car starts.. sometimes it does'nt and it triggers the alarm...

Tried to hard wire the disarm to the "non-present" disarm wire to the BCM.. Not working

Tried to unlock before start in datamode.. sometimes it works..

At first I installed a DSE-503 and a Al-Ca but it was working sometimes.. So I swapped it for a HC2 to have all componants integrated to avoid timing errors



The Customer is mad about that.. I have a last try before to remove all the stuff.. :evil:
André Rousseau
VitrXpert Thetford Mines
2-1550 frontenac E
Thetford Mines, Qc
418-338-6961

User avatar
Murph
Site Admin
Posts: 6507
Joined: Sun Oct 23, 2011 8:35 pm

Re: HC2 with 2008 infinity G35

Post by Murph » Tue Jan 31, 2017 4:40 pm

Did you call tech support so we can help you while you are working on it?
Brian Murphy
MECP Advanced Certified Installer
ADS Tech Support
Automotive Data Solutions inc.
8400, Bougainville, Montreal, QC.
1-866-427-2999
support@idatalink.com

RWarrior
12Volt Specialist
Posts: 11
Joined: Wed Jan 15, 2014 10:08 am

Re: HC2 with 2008 infinity G35

Post by RWarrior » Wed Feb 01, 2017 8:15 am

Yes. I talked to Victor.

I tried to disarm before start on datamode in double pulse unlock. The car did'nt started like if it tried to start before ending the disarm procedure.

Reprogrammed it in single pulse data (don't forget it never worked with a wire in the BCM) and it worked well few times.. until I pulled it out, showing to customer how it would work... and it triggered the alarm instead of cranking :evil: The customer had to leave to work so i did'nt tried anyting else.

When she'll bring the car back friday, i'll try to bring a wire to the windows control switch in the door :roll:
André Rousseau
VitrXpert Thetford Mines
2-1550 frontenac E
Thetford Mines, Qc
418-338-6961

User avatar
Murph
Site Admin
Posts: 6507
Joined: Sun Oct 23, 2011 8:35 pm

Re: HC2 with 2008 infinity G35

Post by Murph » Wed Feb 01, 2017 10:14 am

I prefer to go to the door switch in most Nissan vehicles. Only takes a few minutes.
Brian Murphy
MECP Advanced Certified Installer
ADS Tech Support
Automotive Data Solutions inc.
8400, Bougainville, Montreal, QC.
1-866-427-2999
support@idatalink.com

RWarrior
12Volt Specialist
Posts: 11
Joined: Wed Jan 15, 2014 10:08 am

Re: HC2 with 2008 infinity G35

Post by RWarrior » Fri Feb 03, 2017 3:27 pm

I did it in the door..

Half of the time the car starts on first try, the other on the second try...

Once on 20 tries it did'nt started at all.. Wait 1 minute, wait 5 minutes.. never the same result.. Start the car with keyfob, let it stay few minutes.. same thing

I put my logic probe on the PTS signal, an a test bulb on the Starter/brake signal to see the good syncronisym.. it's fine.. juste like if the car does'nt see the key..


Really weird
André Rousseau
VitrXpert Thetford Mines
2-1550 frontenac E
Thetford Mines, Qc
418-338-6961

User avatar
Murph
Site Admin
Posts: 6507
Joined: Sun Oct 23, 2011 8:35 pm

Re: HC2 with 2008 infinity G35

Post by Murph » Fri Feb 03, 2017 3:34 pm

As long as we have the key away from the car and at lease 2.5-3 seconds on the brake, it should start ever time. Make sure the ground is not on the dash frame. Go to the kick or pin 4 of the OBD2.
Brian Murphy
MECP Advanced Certified Installer
ADS Tech Support
Automotive Data Solutions inc.
8400, Bougainville, Montreal, QC.
1-866-427-2999
support@idatalink.com

RWarrior
12Volt Specialist
Posts: 11
Joined: Wed Jan 15, 2014 10:08 am

Re: HC2 with 2008 infinity G35

Post by RWarrior » Sun Feb 05, 2017 9:46 am

I took the option "Add 600ms" to crank time.
André Rousseau
VitrXpert Thetford Mines
2-1550 frontenac E
Thetford Mines, Qc
418-338-6961

RWarrior
12Volt Specialist
Posts: 11
Joined: Wed Jan 15, 2014 10:08 am

Re: HC2 with 2008 infinity G35

Post by RWarrior » Sun Feb 05, 2017 9:46 am

I took the option "Add 600ms" to crank time.
André Rousseau
VitrXpert Thetford Mines
2-1550 frontenac E
Thetford Mines, Qc
418-338-6961

Post Reply

Return to “iDatastart HC2”