Weblink Mobile
-
- 12Volt Specialist
- Posts: 41
- Joined: Sat Nov 21, 2015 1:39 pm
- Location: Grunthal, Manitoba, Canada
- Contact:
Weblink Mobile
I have programmed HC remote starter with success using the Mobile weblink however I notice even with a PC or with this mobile Weblink that I have to pull the main power fuses for the HC in order for the weblink to detect the module. Is there going to be a fix for this where we wont have to disconnect power to the HC module in order to configure it?
Isaak Doerksen
Phone: 204-355-8464
IR Electronics
27061 PR216
Grunthal, MB
R0A0R0
Canada
Phone: 204-355-8464
IR Electronics
27061 PR216
Grunthal, MB
R0A0R0
Canada
- Murph
- Site Admin
- Posts: 6866
- Joined: Sun Oct 23, 2011 8:35 pm
Re: Weblink Mobile
You can't flash any module with 12v power attached to it. They are not designed to be flashed in the car.
Brian Murphy
MECP Advanced Certified Installer
ADS Tech Support
Automotive Data Solutions inc.
8400, Bougainville, Montreal, QC.
1-866-427-2999
support@idatalink.com
MECP Advanced Certified Installer
ADS Tech Support
Automotive Data Solutions inc.
8400, Bougainville, Montreal, QC.
1-866-427-2999
support@idatalink.com
-
- 12Volt Specialist
- Posts: 41
- Joined: Sat Nov 21, 2015 1:39 pm
- Location: Grunthal, Manitoba, Canada
- Contact:
Re: Weblink Mobile
I understand that they need to be flashed outside the vehicle with the vehicle firmware. However I believe once the firmware has been programmed, you should be able to change remote start setting like how long you want engine to run or any other remote start functions with out removing remote starter or climbing under dash to connect to it.
Just a thought...
Just a thought...
Isaak Doerksen
Phone: 204-355-8464
IR Electronics
27061 PR216
Grunthal, MB
R0A0R0
Canada
Phone: 204-355-8464
IR Electronics
27061 PR216
Grunthal, MB
R0A0R0
Canada
- Murph
- Site Admin
- Posts: 6866
- Joined: Sun Oct 23, 2011 8:35 pm
Re: Weblink Mobile
Unfortunately, there is no way to change settings from a PC or Weblink Mobile without disconnecting power.
Brian Murphy
MECP Advanced Certified Installer
ADS Tech Support
Automotive Data Solutions inc.
8400, Bougainville, Montreal, QC.
1-866-427-2999
support@idatalink.com
MECP Advanced Certified Installer
ADS Tech Support
Automotive Data Solutions inc.
8400, Bougainville, Montreal, QC.
1-866-427-2999
support@idatalink.com
-
- New User
- Posts: 6
- Joined: Sat Jun 04, 2016 8:40 pm
Re: Weblink Mobile
I know you can use an OP500 option programmer for Compustar stuff to do exactly this. It just plugs in at the antenna and away you go...irelectronics wrote:I understand that they need to be flashed outside the vehicle with the vehicle firmware. However I believe once the firmware has been programmed, you should be able to change remote start setting like how long you want engine to run or any other remote start functions with out removing remote starter or climbing under dash to connect to it.
Just a thought...
However, not sure if they are compatible with the starters you are using?
- Murph
- Site Admin
- Posts: 6866
- Joined: Sun Oct 23, 2011 8:35 pm
Re: Weblink Mobile
No the OP500 does not work with HC product.
Brian Murphy
MECP Advanced Certified Installer
ADS Tech Support
Automotive Data Solutions inc.
8400, Bougainville, Montreal, QC.
1-866-427-2999
support@idatalink.com
MECP Advanced Certified Installer
ADS Tech Support
Automotive Data Solutions inc.
8400, Bougainville, Montreal, QC.
1-866-427-2999
support@idatalink.com